A patient specific computational biomechanical model for the entire lumbosacral spinal unit with imposed spondylolysis.
Journal
Clinical biomechanics (Bristol, Avon)
ISSN: 1879-1271
Titre abrégé: Clin Biomech (Bristol, Avon)
Pays: England
ID NLM: 8611877
Informations de publication
Date de publication:
08 2019
08 2019
Historique:
received:
28
01
2019
revised:
31
03
2019
accepted:
13
05
2019
pubmed:
4
6
2019
medline:
2
7
2020
entrez:
4
6
2019
Statut:
ppublish
Résumé
A biomechanical model of the lumbosacral spinal unit between L1-S1 was developed to investigate the behavior of normal and select pathological states. Our aims were to generate predictive structural models for mechanical deformation including critical stresses in the spine components and to investigate the probability of subsequent lumbar spine fractures in the presence of unilateral spondylolysis. A non-linear three-dimensional finite element pathology-free model of the L1-S1 lumbosacral unit was generated using patient-specific computerized tomography scans and calibrated by comparing it to experimental data of a range of motion modes consisting of flexion, extension, left and right lateral bending, and left and right axial rotation. Unilateral and bilateral pars defects were created on the isthmus of L5 to simulate spondylolysis. Results showed that under flexion, left lateral bending and right axial rotation, stresses were higher on the contralateral L5 pars-interarticularis, whereas, no significant changes occurred on the left-right isthmus of the L2-L4 and S1. Significant changes in the range of motion compared to the pathology-free model were observed in bilateral spondylolysis not only adjacent to the pars defect area but also in other lumbar spine levels. The proposed pathology-free lumbosacral unit model showed good correlation with experimental tests for all loading cases. In unilateral spondylolysis, a subsequent pars defect was observed within the same vertebra. The overall modeling approach can be used to study different pathological states.
Sections du résumé
BACKGROUND
A biomechanical model of the lumbosacral spinal unit between L1-S1 was developed to investigate the behavior of normal and select pathological states. Our aims were to generate predictive structural models for mechanical deformation including critical stresses in the spine components and to investigate the probability of subsequent lumbar spine fractures in the presence of unilateral spondylolysis.
METHODS
A non-linear three-dimensional finite element pathology-free model of the L1-S1 lumbosacral unit was generated using patient-specific computerized tomography scans and calibrated by comparing it to experimental data of a range of motion modes consisting of flexion, extension, left and right lateral bending, and left and right axial rotation. Unilateral and bilateral pars defects were created on the isthmus of L5 to simulate spondylolysis.
FINDINGS
Results showed that under flexion, left lateral bending and right axial rotation, stresses were higher on the contralateral L5 pars-interarticularis, whereas, no significant changes occurred on the left-right isthmus of the L2-L4 and S1. Significant changes in the range of motion compared to the pathology-free model were observed in bilateral spondylolysis not only adjacent to the pars defect area but also in other lumbar spine levels.
INTERPRETATION
The proposed pathology-free lumbosacral unit model showed good correlation with experimental tests for all loading cases. In unilateral spondylolysis, a subsequent pars defect was observed within the same vertebra. The overall modeling approach can be used to study different pathological states.
Identifiants
pubmed: 31158588
pii: S0268-0033(19)30062-2
doi: 10.1016/j.clinbiomech.2019.05.022
pii:
doi:
Types de publication
Journal Article
Langues
eng
Sous-ensembles de citation
IM
Pagination
37-44Informations de copyright
Copyright © 2019 Elsevier Ltd. All rights reserved.