Evaluation of the Self-Healing Ability of Mortar Mixtures Containing Superabsorbent Polymers and Nanosilica.

crack width measurement hydrogels nanosilica self-healing concrete water permeability

Journal

Materials (Basel, Switzerland)
ISSN: 1996-1944
Titre abrégé: Materials (Basel)
Pays: Switzerland
ID NLM: 101555929

Informations de publication

Date de publication:
14 Jan 2020
Historique:
received: 11 12 2019
revised: 08 01 2020
accepted: 10 01 2020
entrez: 18 1 2020
pubmed: 18 1 2020
medline: 18 1 2020
Statut: epublish

Résumé

Addition of superabsorbent polymers (SAPs) to cementitious mixtures promotes the self-healing ability of the material. When cracking occurs; SAPs present inside the crack will swell upon contact with water and subsequently release this water to stimulate the further hydration of unhydrated cement particles and the calcium carbonate crystallization. However; the inclusion of SAPs affects the mechanical performance of the cementitious material by the creation of macro-pores as water is retracted from the swollen SAP. To counteract the reduction in strength, part of the cement is replaced by nanosilica. In this research, different mixtures containing either SAPs or nanosilica and a combination of both were made. The samples were subjected to wet-dry cycles simulating external conditions, and the self-healing efficiency was evaluated by means of the evolution in crack width, by optical measurements, and a water permeability test. In samples containing SAPs, an immediate sealing effect was observed and visual crack closure was noticed. The smaller influence on the mechanical properties and the good healing characteristics in mixtures containing both nanosilica and SAPs are promising as a future material for use in building applications.

Identifiants

pubmed: 31947606
pii: ma13020380
doi: 10.3390/ma13020380
pmc: PMC7013588
pii:
doi:

Types de publication

Journal Article

Langues

eng

Subventions

Organisme : Fonds Wetenschappelijk Onderzoek
ID : G.0A28.16.6

Déclaration de conflit d'intérêts

The authors declare no conflict of interest.

Références

Materials (Basel). 2013 May 27;6(6):2182-2217
pubmed: 28809268

Auteurs

Gerlinde Lefever (G)

Department Mechanics of Materials and Constructions, Vrije Universiteit Brussel (VUB), Pleinlaan 2, 1050 Brussels, Belgium.

Didier Snoeck (D)

Department Mechanics of Materials and Constructions, Vrije Universiteit Brussel (VUB), Pleinlaan 2, 1050 Brussels, Belgium.
Magnel-Vandepitte Laboratory for Building Materials and Structures, Department of Structural Engineering and Building Materials, Faculty of Engineering and Architecture, Ghent University, Tech Lane Ghent Science Park, Technologiepark Zwijnaarde 60, 9052 Ghent, Belgium.

Dimitrios G Aggelis (DG)

Department Mechanics of Materials and Constructions, Vrije Universiteit Brussel (VUB), Pleinlaan 2, 1050 Brussels, Belgium.

Nele De Belie (N)

Magnel-Vandepitte Laboratory for Building Materials and Structures, Department of Structural Engineering and Building Materials, Faculty of Engineering and Architecture, Ghent University, Tech Lane Ghent Science Park, Technologiepark Zwijnaarde 60, 9052 Ghent, Belgium.

Sandra Van Vlierberghe (S)

Polymer Chemistry & Biomaterials Research Group, Centre of Macromolecular Chemistry, Ghent University, Krijgslaan 281 S4-Bis, 9000 Ghent, Belgium.

Danny Van Hemelrijck (D)

Department Mechanics of Materials and Constructions, Vrije Universiteit Brussel (VUB), Pleinlaan 2, 1050 Brussels, Belgium.

Classifications MeSH