Cryogenically treated and untreated stainless steel grade 317 in sustainable wire electrical discharge machining process: a comparative study.
Cryogenic treatment
Cutting rate
Oxygen mist
Stainless steel grade 317
Wire wear ratio
Journal
Environmental science and pollution research international
ISSN: 1614-7499
Titre abrégé: Environ Sci Pollut Res Int
Pays: Germany
ID NLM: 9441769
Informations de publication
Date de publication:
Sep 2023
Sep 2023
Historique:
received:
11
05
2022
accepted:
29
08
2022
medline:
5
10
2023
pubmed:
4
9
2022
entrez:
3
9
2022
Statut:
ppublish
Résumé
In this research, the influences of cryogenically treated stainless steel grade 317 on the eco-friendly near-dry wire-cut electrical discharge machining (NDWEDM) processes have been investigated using the minimum quantity of water mixed with oxygen gas (oxygen mist) dielectric fluid. The stainless steel grade 317 has been applied to make the various biomedical and industrial components due to its high creep strength. The wire wear ratio (WWR) and cutting rate (CR) of NDWEDM are compared using cryogenically treated and untreated work materials by Taguchi's analysis. The water flow rate, gas pressure, spark current, and pulse width had been considered as process parameters. The microstructure of wire electrode and machined surfaces of treated/untreated materials had been compared by scanning electron microscope (SEM) images. The WWR and CR of cryogenically treated materials in NDWEDM are 20.31% lower and 22.32% higher than untreated materials, respectively.
Identifiants
pubmed: 36057706
doi: 10.1007/s11356-022-22843-x
pii: 10.1007/s11356-022-22843-x
doi:
Substances chimiques
Stainless Steel
12597-68-1
Water
059QF0KO0R
Oxygen
S88TT14065
Types de publication
Journal Article
Langues
eng
Sous-ensembles de citation
IM
Pagination
99036-99045Informations de copyright
© 2022. The Author(s), under exclusive licence to Springer-Verlag GmbH Germany, part of Springer Nature.
Références
Abdulkareem S, Khan AA, Konneh M (2009) Reducing electrode wear ratio using cryogenic cooling during electrical discharge machining. Int J Adv Manuf Technol 45:1146–1151. https://doi.org/10.1007/s00170-009-2060-5
doi: 10.1007/s00170-009-2060-5
Akincioğlu S, Gökkaya H, Uygur İ (2015) A review of cryogenic treatment on cutting tools. Int J Adv Manuf Technol 78:1609–1627
doi: 10.1007/s00170-014-6755-x
Amorim FL, Torres RD, Laurindo CAH, Reolon LW (2019) Performance and surface integrity of wire electrical discharge machining of thin Ti6Al4V plate using coated and uncoated wires. Mater Res 22:4–9. https://doi.org/10.1590/1980-5373-MR-2019-0127
doi: 10.1590/1980-5373-MR-2019-0127
Bekmurzayeva A, Duncanson WJ, Azevedo HS, Kanayeva D (2018) Surface modification of stainless steel for biomedical applications: revisiting a century-old material. Mater Sci Eng C 93:1073–1089. https://doi.org/10.1016/j.msec.2018.08.049
doi: 10.1016/j.msec.2018.08.049
Boopathi S (2021) An investigation on gas emission concentration and relative emission rate of the near-dry wire-cut electrical discharge machining process. Environ Sci Pollut Res 1–10. https://doi.org/10.1007/s11356-021-17658-1
Boopathi S (2022a) An extensive review on sustainable developments of dry and near-dry electrical discharge machining processes. J Manuf Sci Eng 144(5):050801. https://doi.org/10.1115/1.4052527
doi: 10.1115/1.4052527
Boopathi S (2022b) Performance improvement of eco-friendly near-dry wire-cut electrical discharge machining process using coconut oil-mist dielectric fluid. J Adv Manuf Syst. https://doi.org/10.1142/s0219686723500178
doi: 10.1142/s0219686723500178
Boopathi S, Lewise KAS, Subbiah R, Sivaraman G (2021) Near-dry wire-cut electrical discharge machining process using water-air-mist dielectric fluid: an experimental study. Mater Today Proc 49:1885–1890. https://doi.org/10.1016/j.matpr.2021.08.077
doi: 10.1016/j.matpr.2021.08.077
Boopathi S, Myilsamy S (2021) Material removal rate and surface roughness study on near-dry wire electrical discharge Machining process. Mater Today Proc 45:8149–8156. https://doi.org/10.1016/j.matpr.2021.02.267
doi: 10.1016/j.matpr.2021.02.267
Boopathi S, Sivakumar K (2013) Experimental investigation and parameter optimization of near-dry wire-cut electrical discharge machining using multi-objective evolutionary algorithm. Int J Adv Manuf Technol 67:2639–2655. https://doi.org/10.1007/s00170-012-4680-4
doi: 10.1007/s00170-012-4680-4
Boopathi S, Sivakumar K (2014) Study of water assisted dry wire-cut electrical discharge machining. Indian J Eng Mater Sci 21:75–82. http://nopr.niscair.res.in/handle/123456789/27453
Boopathi S, Sivakumar K (2016) Optimal parameter prediction of oxygen-mist near-dry wire-cut EDM. Int J Manuf Technol Manag 30:164–178. https://doi.org/10.1504/IJMTM.2016.077812
doi: 10.1504/IJMTM.2016.077812
Boopathi S, Sivakumar K, Kalidas R (2012) Parametric study of dry WEDM using Taguchi method. Int J Eng Res Dev 2:1–6
Chityal NS, Bhandare A, Dabade UA (2019) Experimental investigation on a shield and magnetic assisted EDM of EN24 steel. Mater Today Proc 19:594–598. https://doi.org/10.1016/j.matpr.2019.08.075
doi: 10.1016/j.matpr.2019.08.075
De Mello Belentani R, Júnior HF, Canarim RC et al (2014) Utilization of minimum quantity lubrication (MQL) with water in CBN grinding of steel. Mater Res 17:88–96. https://doi.org/10.1590/S1516-14392013005000165
doi: 10.1590/S1516-14392013005000165
Dhakar K, Chaudhary K, Dvivedi A, Bembalge O (2019) An environment-friendly and sustainable machining method: near-dry EDM. Mater Manuf Process 34:1307–1315. https://doi.org/10.1080/10426914.2019.1643471
doi: 10.1080/10426914.2019.1643471
Fard RK, Afza RA, Teimouri R (2013) Experimental investigation, intelligent modeling and multi-characteristics optimization of dry WEDM process of Al-SiC metal matrix composite. J Manuf Process 15:483–494. https://doi.org/10.1016/j.jmapro.2013.09.002
doi: 10.1016/j.jmapro.2013.09.002
Ganachari VS, Chate UN, Waghmode LY et al (2019) A comparative performance study of dry and near dry EDM processes in machining of spring steel material. Mater Today Proc 18:5247–5257. https://doi.org/10.1016/j.matpr.2019.07.525
doi: 10.1016/j.matpr.2019.07.525
Garg MP, Kumar A, Sahu CK (2017) Mathematical modeling and analysis of WEDM machining parameters of nickel-based super alloy using response surface methodology. Sadhana - Acad Proc Eng Sci 42:981–1005. https://doi.org/10.1007/s12046-017-0647-3
doi: 10.1007/s12046-017-0647-3
Goyal A, Pandey A, Sharma P (2017) An experimental study of aerospace material during fabrication of V groove using wedm. Int J Mech Prod Eng Res Dev 7:249–258. https://doi.org/10.24247/ijmperdjun201726
doi: 10.24247/ijmperdjun201726
Gunasekaran K, Boopathi S, Sureshkumar M (2022) Analysis of a cryogenically cooled near-dry WEDM process using different dielectrics. Mater Tehnol 56:179–186. https://doi.org/10.17222/mit.2022.397
doi: 10.17222/mit.2022.397
Jadhav PS, Mohanty CP (2022) Performance assessment of energy efficient and eco-friendly turning of Nimonic C-263: a comparative study on MQL and cryogenic machining. Proc Inst Mech Eng Part B J Eng Manuf 236:1125–1140. https://doi.org/10.1177/09544054211061961
doi: 10.1177/09544054211061961
Jafferson JM, Hariharan P (2013) Machining performance of cryogenically treated electrodes in microelectric discharge machining: a comparative experimental study. Mater Manuf Process 28:397–402. https://doi.org/10.1080/10426914.2013.763955
doi: 10.1080/10426914.2013.763955
Kalsi NS, Sehgal R, Sharma VS (2010) Cryogenic treatment of tool materials: a review. Mater Manuf Process 25:1077–1100
doi: 10.1080/10426911003720862
Kannan E, Trabelsi Y, Boopathi S, Alagesan S (2022) Influences of cryogenically treated work material on near-dry wire-cut electrical discharge machining process. Surf Topogr Metrol Prop 10:. https://doi.org/10.1088/2051-672X/ac53e1
Kennedy D (2001) Cryogenic treatment enhances stability for wire EDM operation. Wire
Kumar SV, Kumar MP (2015) Experimental investigation of the process parameters in cryogenic cooled electrode in EDM. J Mech Sci Technol 29:3865–3871. https://doi.org/10.1007/s12206-015-0832-4
doi: 10.1007/s12206-015-0832-4
Mohammed MT (2018) Investigate WEDM process parameters on wire wear ratio, material removal rate and surface roughness of steel 1012 AISI. Eng Technol J 36:. https://doi.org/10.30684/etj.36.3a.3
Mohanty CP, Satpathy MP, Mahapatra SS, Singh MR (2018) Optimization of cryo-treated EDM variables using TOPSIS-based TLBO algorithm. Sadhana - Acad Proc Eng Sci 43:1–18. https://doi.org/10.1007/s12046-018-0829-7
doi: 10.1007/s12046-018-0829-7
Myilsamy S, Sampath B (2021) Experimental comparison of near-dry and cryogenically cooled near-dry machining in wire-cut electrical discharge machining processes. Surf Topogr Metrol Prop 9:035015. https://doi.org/10.1088/2051-672X/ac15e0
doi: 10.1088/2051-672X/ac15e0
Myilsamy S, Boopathi S, Yuvaraj D (2021) A study on cryogenically treated molybdenum wire electrode. Mater Today Proc 45(9):8130–8135. https://doi.org/10.1016/j.matpr.2021.02.049
doi: 10.1016/j.matpr.2021.02.049
Nandhakumar S, Sathish Kumar S, Sakthivelu K (2018) Optimization of machining variables in electric discharge machining using stainless steel 317 in full factorial method. Mech Mech Eng 22:105–117. https://doi.org/10.2478/mme-2018-0010
doi: 10.2478/mme-2018-0010
Pramanik A, Basak AK (2018) Sustainability in wire electrical discharge machining of titanium alloy: understanding wire rupture. J Clean Prod 198:472–479. https://doi.org/10.1016/j.jclepro.2018.07.045
doi: 10.1016/j.jclepro.2018.07.045
Saha SK, Choudhury SK (2009) Experimental investigation and empirical modeling of the dry electric discharge machining process. Int J Mach Tools Manuf 49:297–308. https://doi.org/10.1016/j.ijmachtools.2008.10.012
doi: 10.1016/j.ijmachtools.2008.10.012
Sampath B, Sureshkumar M, Yuvaraj T, Velmurugan D (2021) Experimental investigations on eco-friendly helium-mist near-dry wire-cut edm of m2-hss material. Mater Res Proc Mater Res Forum 19:175–180. https://doi.org/10.21741/9781644901618-22
Sampath B, Myilsamy S (2021) Experimental investigation of a cryogenically cooled oxygen-mist near-dry wire-cut electrical discharge machining process. Stroj Vestnik/journal Mech Eng 67:322–330. https://doi.org/10.5545/sv-jme.2021.7161
doi: 10.5545/sv-jme.2021.7161
Shastri RK, Mohanty CP (2021) Sustainable electrical discharge machining of nimonic C263 superalloy. Arab J Sci Eng 46:7273–7293. https://doi.org/10.1007/s13369-020-05211-0
doi: 10.1007/s13369-020-05211-0
Singh H, Singh A (2012) Wear behavior of AISI D3 die steel using cryogenic treated copper and brass electrode in electric discharge machining. Int J Mod Eng Res 2:4462–4464
Srivastava V, Pandey PM (2012) Performance evaluation of electrical discharge machining (EDM) process using cryogenically cooled electrode. Mater Manuf Process 27:683–688. https://doi.org/10.1080/10426914.2011.602790
doi: 10.1080/10426914.2011.602790
Srivastava V, Pandey PM (2012) Effect of process parameters on the performance of EDM process with ultrasonic assisted cryogenically cooled electrode. J Manuf Process 14:393–402. https://doi.org/10.1016/j.jmapro.2012.05.001
doi: 10.1016/j.jmapro.2012.05.001
Sundriyal S, Vipin, Walia RS (2020) Study on the influence of metallic powder in near-dry electric discharge machining. Stroj Vestnik/Journal Mech Eng 66:243–253. https://doi.org/10.5545/sv-jme.2019.6475
doi: 10.5545/sv-jme.2019.6475
Valaki JB, Rathod PP (2016) Assessment of operational feasibility of waste vegetable oil based bio-dielectric fluid for sustainable electric discharge machining (EDM). Int J Adv Manuf Technol 87:1509–1518. https://doi.org/10.1007/s00170-015-7169-0
doi: 10.1007/s00170-015-7169-0
Valaki JB, Rathod PP, Khatri BC (2015) Environmental impact, personnel health and operational safety aspects of electric discharge machining: a review. Proc Inst Mech Eng Part B J Eng Manuf 229:1481–1491. https://doi.org/10.1177/0954405414543314
doi: 10.1177/0954405414543314
Yadav VK, Kumar P, Dvivedi A (2019) Performance enhancement of rotary tool near-dry EDM of HSS by supplying oxygen gas in the dielectric medium. Mater Manuf Process 34:1832–1846. https://doi.org/10.1080/10426914.2019.1675889
doi: 10.1080/10426914.2019.1675889
Yupapin P, Trabelsi Y, Nattappan A, Boopathi S (2022) Performance improvement of wire - cut electrical discharge machining process using cryogenically treated super - conductive state of Monel - K500 alloy. Iran J Sci Technol Trans Mech Eng. https://doi.org/10.1007/s40997-022-00513-0
doi: 10.1007/s40997-022-00513-0