Microplastics Removal Efficiency and Risk Analysis of Wastewater Treatment Plants in Oman.

Emerging pollutants Microplastics PROMETHEE method Plastic polymers Wastewater treatment technologies

Journal

Chemosphere
ISSN: 1879-1298
Titre abrégé: Chemosphere
Pays: England
ID NLM: 0320657

Informations de publication

Date de publication:
04 May 2024
Historique:
received: 07 11 2023
revised: 12 04 2024
accepted: 29 04 2024
medline: 7 5 2024
pubmed: 7 5 2024
entrez: 6 5 2024
Statut: aheadofprint

Résumé

Microplastics (MPs) have recently been documented as an emerging pollutant that poses a critical threat to environment. Wastewater treatment plants (WWTPs) are commonly regarded as significant contributors to the presence of MPs. This study aimed to assess the MPs load of three wastewater treatment facilities in Oman using various treatments, including MBR, SBR, and CAS. Wastewater samples from influent, effluent, and sludge were collected and analyzed to determine the concentration, morphology, size, color, and polymer type of the MPs. A set of sieves with a mesh size range of 1 mm to 45 μm was used to for filteration. Oxidation treatment was applied for all samples using Fenton's reagent, followed by density separation by sodium chloride solution. The Attenuated Total Reflectance Fourier Transform Infrared Spectroscopy (ATR- FTIR) method was utilized to test 10% from each sampling point to confirm the polymer types of the MPs. The pollution load index (PLI) and hazard index (HI) have been employed to assess the risk associated with the chemical toxicity and concentration of detected particles. The PROMETHEE method was used to rank the risk of sampling sites based on different criteria that posed potential ecological and human health risks. The results indicate that the average concentrations of 0.99 MPs/L, 1.38 MPs/L, and 0.93 MPs/L were detected in the final treated effluent of WWTP A, WWTP B, and WWTP C, respectively. These concentrations correspond to overall removal efficiencies of 82.5%, 77.4%, and 79.2% for WWTP A, WWTP B, and WWTP C, respectively Most MPs found in tertiary effluent were smaller particles (425μm) and fiber-shaped. The major types of MPs were polypropylene (PP), low-density polyethylene (LDPE), polyurethane (PU), polyethylene terephthalate (PET), and Polyvinyl chloride (PVC). This study showed that treated effluent and sludge release significant MPs into the environment.

Identifiants

pubmed: 38710411
pii: S0045-6535(24)01099-3
doi: 10.1016/j.chemosphere.2024.142206
pii:
doi:

Types de publication

Journal Article

Langues

eng

Sous-ensembles de citation

IM

Pagination

142206

Informations de copyright

Copyright © 2024. Published by Elsevier Ltd.

Déclaration de conflit d'intérêts

Declaration of Competing Interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper. The authors declare the following financial interests/personal relationships which may be considered as potential competing interests:

Auteurs

Abrar Al-Amri (A)

Department of Civil and Architectural Engineering, Sultan Qaboos University, Muscat, Oman. Electronic address: s132299@student.squ.edu.om.

Zeinab Yavari (Z)

Department of Civil and Architectural Engineering, Sultan Qaboos University, Muscat, Oman. Electronic address: z.yavari@squ.edu.om.

Mohammad Reza Nikoo (M)

Department of Civil and Architectural Engineering, Sultan Qaboos University, Muscat, Oman. Electronic address: m.reza@squ.edu.om.

Maryam Karimi (M)

School of Public Health, Department of Environmental Health Sciences, University of Alabama at Birmingham, USA. Electronic address: karimi@uab.edu.

Classifications MeSH