Investigating desiccation resistance, post-rehydration growth, and heat tolerance in desiccation-injured cells of Salmonella enterica isolated from the soybean production chain.

Drying Low water activity foods Recovery Stress Thermal resistance Variability

Journal

International journal of food microbiology
ISSN: 1879-3460
Titre abrégé: Int J Food Microbiol
Pays: Netherlands
ID NLM: 8412849

Informations de publication

Date de publication:
16 Nov 2023
Historique:
received: 23 04 2023
revised: 28 08 2023
accepted: 31 08 2023
medline: 25 9 2023
pubmed: 7 9 2023
entrez: 6 9 2023
Statut: ppublish

Résumé

This study compared the resistance to different desiccation conditions of 190 Salmonella enterica strains previously isolated from the soybean meal production chain and belonging to 23 serovars. Additionally, the post-rehydration growth and heat tolerance of the strains previously exposed to desiccation were determined. Variability in desiccation resistance was observed both within and between serovars. Strains belonging to S. Havana and S. Schwarzengrund serovars were the most resistant, regardless of storage condition. The drying temperature (20 °C and 30 °C) did not influence the desiccation resistance of the Salmonella strains. On the other hand, increasing drying time from 1 to 7 days reduced Salmonella counts. The origin (isolation sources) also influenced the desiccation resistance of the Salmonella strains. The growth of the Salmonella strains after rehydration varied considerably depending on the drying conditions and incubation temperature during cultivation. An increase in the time and temperature of drying led to a reduction in population of most Salmonella strains after rehydration. Salmonella strains previously desiccated also showed differences in the heat tolerance in all temperature-time binomials tested. Some strains were highly resistant to heat tolerance conditions, presenting <1 log CFU/mL reduction from the initial population. The results obtained in this study suggest that the strategies to mitigate Salmonella in low-a

Identifiants

pubmed: 37672943
pii: S0168-1605(23)00303-3
doi: 10.1016/j.ijfoodmicro.2023.110387
pii:
doi:

Types de publication

Journal Article

Langues

eng

Sous-ensembles de citation

IM

Pagination

110387

Informations de copyright

Copyright © 2023 Elsevier B.V. All rights reserved.

Déclaration de conflit d'intérêts

Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper.

Auteurs

Marianna M Furtado (MM)

Department of Food Science and Nutrition, Faculty of Food Engineering, University of Campinas, Campinas, SP, Brazil.

Beatriz S Silva (BS)

Department of Food Science and Nutrition, Faculty of Food Engineering, University of Campinas, Campinas, SP, Brazil.

Luísa Freire (L)

Department of Food Science and Nutrition, Faculty of Food Engineering, University of Campinas, Campinas, SP, Brazil.

Juliana S Graça (JS)

Department of Food Science and Nutrition, Faculty of Food Engineering, University of Campinas, Campinas, SP, Brazil.

Verônica O Alvarenga (VO)

Department of Food Science and Nutrition, Faculty of Food Engineering, University of Campinas, Campinas, SP, Brazil; Department of Food, Faculty of Pharmacy, Federal University of Minas Gerais, Belo Horizonte, MG, Brazil.

Humberto M Hungaro (HM)

Department of Pharmaceutical Sciences, Faculty of Pharmacy, Federal University of Juiz de Fora, Juiz de Fora, MG, Brazil.

Anderson S Sant'Ana (AS)

Department of Food Science and Nutrition, Faculty of Food Engineering, University of Campinas, Campinas, SP, Brazil. Electronic address: and@unicamp.br.

Articles similaires

Glycine max Photoperiod Ubiquitin-Protein Ligases Flowers Gene Expression Regulation, Plant
Rhizosphere Glycine max Seeds Soybean Oil Soil Microbiology
Glycine max Seeds Transcription Factors Gene Expression Regulation, Plant Plant Proteins
Animals Aquatic Organisms Ecosystem Oxygen Thermotolerance

Classifications MeSH