3D-printed orthoses and prostheses for people with physical disability in rehabilitation centers: a scoping review.
Artificial limbs
Orthotic devices
People with disability
Rehabilitation centers
Three-dimensional printing
Journal
BMC musculoskeletal disorders
ISSN: 1471-2474
Titre abrégé: BMC Musculoskelet Disord
Pays: England
ID NLM: 100968565
Informations de publication
Date de publication:
04 Oct 2024
04 Oct 2024
Historique:
received:
09
04
2024
accepted:
16
09
2024
medline:
5
10
2024
pubmed:
5
10
2024
entrez:
4
10
2024
Statut:
epublish
Résumé
The World Health Organization points out that, by 2030, two billion people will need at least one assistive product. 3D printing can be used to meet the demands when dispensing these products. This review aims to map the use of 3D printing in the manufacture of orthoses and prostheses for people with physical disability at rehabilitation centers. Publications that deal with the use of 3D printing for the manufacture of orthoses and prostheses were used, preferably studies from 2012 to 2022. The majority of studies, 56.25%, were quantitative and 46.25% were evaluative research. None of the studies were characterized as developed at rehabilitation centers. 75% of them had the participation of people with physical disability. The use of 3D printing was, for the most part, for the development of assistive technologies for the upper limbs at 56.25%, while 31.25% were for the lower limbs. The assistive products developed were orthoses and prostheses for the wrist, hands, fingers, upper limbs, writing devices, sockets, knees, and feet. Although there were positive results in their performance, some limitations related to strength, stiffness, and resistance were observed.
Identifiants
pubmed: 39367410
doi: 10.1186/s12891-024-07875-3
pii: 10.1186/s12891-024-07875-3
doi:
Types de publication
Journal Article
Review
Systematic Review
Langues
eng
Sous-ensembles de citation
IM
Pagination
783Informations de copyright
© 2024. The Author(s).
Références
Brasil. Ministério da Saúde (MS). Portaria N
Brasil. Lei N
World Health Organization (WHO). Improving access to assistive technology [Internet]. 2017 [acessado 2023 jun 14]. Disponível em: https://www.who.int/activities/improving-access-to-assistive-technology
Castaneda L. Conceito e classificação de órteses. In: Universidade Aberta do SUS. Universidade Federal do Maranhão. Atenção à pessoa com deficiência I: transtornos do espectro do autismo, Síndrome de Down, pessoa idosa comdeficiência, pessoa amputada e órteses, próteses e meios auxiliares de locomoção. Prescrição, Concessão, Adaptação eManutenção de Órteses, Próteses e Meios Auxiliares de Locomoção [Internet]. 2021 [acessado 2023 jun 14]. Disponível em: https://webcache.googleusercontent.com/search?q=cache:gDcAsZ_vMKgJ:https://ares.unasus.gov.br/acervo/bitstream/ARES/24534/1/Folder%2520Conceito%2520e%2520classifca%25C3%25A7%25C3%25A3o%2520de%2520%25C3%25B3rtese.pdf&cd=1&hl=pt-BR&ct=clnk&gl=br
Castaneda L. Próteses de membros superiores e inferiores: indicações e confecção. In: Universidade Aberta do SUS. Universidade Federal do Maranhão. Atenção à pessoa com deficiência I: transtornos do espectro do autismo, Síndrome de Down, pessoa idosa com deficiência, pessoa amputada e órteses, próteses e meios auxiliares de locomoção. Prescrição, Concessão, Adaptação e Manutenção de Órteses, Próteses e Meios Auxiliares de Locomoção [Internet]. 2021 [acessado em 2023 jun 14] Disponível em: https://ares.unasus.gov.br/acervo/html/ARES/24252/1/Pr%C3%B3teses%20de%20membros%20superiores%20e%20inferiores%20indica%C3%A7%C3%B5es%20e%20confec%C3%A7%C3%A3o.pdf
World Health Organization (WHO). Assistive technology [Internet]. 2023 [acessado 2023 jun 14]. Disponível em: https://www.who.int/news-room/fact-sheets/detail/assistive-technology
World Health Organization (WHO). Lista de Produtos Assistivos Prioritários [Internet]. 2017 [acessado 2023 jun 14]. Disponível em: https://apps.who.int/iris/bitstream/handle/10665/207694/WHO-EMP-PHI-2016.01-por.pdf?sequence=14&isAllowed=y
World Health Organization (WHO). Normas de ortoprotésica de la OMS. Parte 1 [Internet]. 2017 [acessado 2023 jun 14]. Disponível em: https://apps.who.int/iris/bitstream/handle/10665/259508/9789243512488-part1-spa.pdf;sequence=1
Brasil. Ministério da Saúde (MS). Guia para Prescrição, Concessão, Adaptação e Manutenção de Órteses, Próteses e Meios Auxiliares de Locomoção [Internet]. 2019 [acessado 2023 jun 14]. Disponível em: https://bvsms.saude.gov.br/bvs/publicacoes/guia_manutencao_orteses_proteses_auxiliares_locomocao.pdf
Borges CA. Impressão 3D para órteses, próteses e materiais especiais: cenário da produção e uso potencial de conhecimento no brasil [dissertação]. Rio de Janeiro (RJ): Fundação Oswaldo Cruz; 2021.
Júnior JLR, Cruz LM, de Sarmanho S. APS. Impressora 3D no desenvolvimento das pesquisas com próteses. Revisbrato [periódico na Internet]. 2018 [acessado 2023 Fev 10]; 2(2). Disponível em: https://revistas.ufrj.br/index.php/ribto/article/view/15022
Instituto. Pesquisa nacional de saúde: 2019: ciclos de vida. [Internet]. Gov.br, 2019. [acessado 2023 Fev 10]. Disponível em: https://biblioteca.ibge.gov.br/index.php/biblioteca-catalogo?id=2101846&view=detalhes
Tricco AC, Lili E, Zarin W, O’Brien KK, Colquhoun H, Levac D, Moher D, Peters MDJ, Horsley T, Weeks L, Hempel S, Akl EA, Chang C, McGowan J, Stewart L, Hartling L, Aldcroft A, Wilson MG, Garritty C, Lewin S, Godfrey CM, Macdonald MT, Lanlois EV, Soares-Weiser K, Moriarty J, Clifford T, Tunçalp O, Straus SE. PRISMA Extension for scoping reviews (PRISMA-ScR): Checklist and Explanation. Annals of Internal Medicine [periódico na Internet]. 2018 [acessado 2023 Fev 10]; Disponível em: https://www.acpjournals.org/doi.org/10.7326/M18-0850
Hitzeroth S, Rehg M, Hogan A, Trinler U. 3D-printed foot prosthesis during gait: Comparison with two standard prostheses. Gait & Posture [periódico na Internet]. 2020 [citado 19 de fevereiro de 2023];81:147–8. Disponível em: https://www-sciencedirect.ez39.periodicos.capes.gov.br/science/article/pii/S0966636220303507
Schmitz C. Proposta De protocolo para o desenvolvimento e avaliação de órtese customizada de punho-mão utilizando tecnologias 3D [dissertação]. Curitiba (PR). Universidade Tecnológica Federal do Paraná; 2019.
Poier PH. Modelo De referência para o desenvolvimento de órteses por manufatura aditiva de baixo custo [tese]. Curitiba (PR): Universidade Tecnológica Federal do Paraná; 2020.
Carter-Davies D, Chen J, Chen F, Li M, Yang C. Mechatronic Design and Control of a 3D Printed Low Cost Robotic Upper Limb. Institute of Electrical and Eletronics Engineers [journal on the Internet]. 2018 [cited 2023 Feb 10]; [about 6 p.]. Available from: https://ieeexplore.ieee.org/document/8633519/authors#authors
South BJ, Fey NP, Bosker G, Neptune RR. Manufacture of Energy Storage and Return Prosthetic Feet Using Selective Laser Sintering. Journal of Biomechanical Engineering [journal on the Internet]. 2009 [cited 2023 Feb 10];132(1). Available from: https://doi.org/10.1115/1.4000166
Webber CM, Davis BL. Design of a novel prosthetic socket: Assessment of the thermal performance. Journal of Biomechanics [journal on the Internet]. [cited 2023 Feb 10];48(7):1294–9. Available from: https://www-sciencedirect.ez39.periodicos.capes.gov.br/science/article/pii/S0021929015001402
Gretsch KF, Lather HD, Peddada KV, Deeken CR, Wall LB, Goldfarb CA. Development of novel 3D-printed robotic prosthetic for transradial amputees. Prosthetics and Orthotics International [journal on the Internet]. 2016 [cited 2023 Feb 19];40(3):400. Available from: https://journals.lww.com/poijournal/Abstract/2016/40030/Development_of_novel_3D_printed_robotic_prosthetic.15.aspx
Zuniga JM, Peck JL, Srivastava R, Pierce JE, Dudley DR, Than NA, Stergiou N. Functional changes through the usage of 3D-printed transitional prostheses in children. Disability and Rehabilitation: Assistive Technology [journal on the Internet]. 2019 [cited 2023 Feb 19];14(1):68–74. Available from: https://www-tandfonline.ez39.periodicos.capes.gov.br/doi/full/10.1080/17483107.2017.1398279
Spicher L, Gershenson J. Key Factors of Design: 3D Printed Occupational Therapy Products in Developing Communities. IEEE Global Humanitarian [journal on the Internet]. 2020 [cited 2023 Feb 19]. [about 7 p]. Available from: https://ieeexplore.ieee.org/document/9342963
Thomann G, de Carvalho VA. Personalized upper limb orthosis necessitates variety of tools during the development process: hemiplegic child case study. Disability and Rehabilitation: Assistive Technology [journal on the Internet]. 2021 [cited 2023 Feb 19];16(2):188–95. Available from: https://www-tandfonline.ez39.periodicos.capes.gov.br/doi/full/10.1080/17483107.2019.1646820
Yoshikawa M, Sato R, Higashihara T, Ogasawara T, Kawashima N, Rehand. Realistic electric prosthetic hand created with a 3D printer. IEEE Eng Med Biol Soc. [journal on the Internet]. 2015 [cited 2023 Feb 19]; 2470–3. Available from: https://ieeexplore.ieee.org/document/7318894
Ramakrishnan T, Schlafly M, Reed KB. Evaluation of 3D printed anatomically scalable transfemoral prosthetic knee. IEEE Eng Med Biol Soc. [journal on the Internet]. 2017[cited 2023 Feb 19];1160–4. Available from: https://ieeexplore.ieee.org/document/8009406/authors#authors
Olsen J, Day S, Dupan S, Nazarpour K, Dyson M. 3D-Printing and Upper-Limb Prosthetic Sockets: Promises and Pitfalls. IEEE Transactions on Neural Systems and Rehabilitation Engineering [journal on the Internet]. 2021[cited 2023 Feb 19];29:527–35. Available from: https://ieeexplore.ieee.org/document/9354240
Tzeng MJ, Hsu LH, Chang SH. Development and evaluation of a cad/3dp process for transtibial socket fabrication. Biomed Eng Appl Basis Commun [jornal on the Internet]. 2015 [cited 2023 Feb 19];27(05):1550044. Available from: https://www-worldscientific-com.ez39.periodicos.capes.gov.br/doi/abs/10.4015/S1016237215500441
Degerli YI, Dogu F, Oksuz C. Manufacturing an assistive device with 3D printing technology - a case report. Assist Technol [jornal on the Internet]. 2022 [cited 2023 Feb 19];121–5. Available from: https://doi.org/10.1080/10400435.2020.1791278
Lee KH, Kim DK, Cha YH, Kwon JY, Kim DH, Kim SJ. Personalized assistive device manufactured by 3D modelling and printing techniques, Disability and Rehabilitation: Assistiv Technology [jornal on the Internet]. 2019 [cited 2023 Feb 19] 14:5, 526–531, Available from: https://www.tandfonline.com/doi/full/10.1080/17483107.2018.1494217
Kuo FL, Wu YS, Kuo TY, Lee YS, Huang SW, Lee HC. Effects of 3D-printed assistive device on daily life function in patients with neurological impairment: a pilot study, Disability and Rehabilitation: Assistive Technology [jornal on the Internet]. 2023 [cited 2023 Jun 23]. Available from: https://www.tandfonline.com/doi/full/10.1080/17483107.2023.2227222