School of Environment, State Key Joint Laboratory of Environment Simulation and Pollution Control, Tsinghua University, Beijing 100084, China; xilu@tsinghua.edu.cn mbm@seas.harvard.edu.
Institute for Carbon Neutrality, Tsinghua University, Beijing 100084, China.
Institute of Environmental Process, College of Environmental and Resource Sciences, Zhejiang University, Hangzhou 310058, PR China. Electronic address: dgq@zju.edu.cn.
Department of Chemical Science and Engineering, School of Materials and Chemical Technology, Tokyo Institute of Technology, 4259 Nagatsuta-cho, Midori-ku, Yokohama, Kanagawa, 226-8502, Japan.
Department of Chemical Science and Engineering, School of Materials and Chemical Technology, Tokyo Institute of Technology, 4259 Nagatsuta-cho, Midori-ku, Yokohama, Kanagawa, 226-8502, Japan.
Department of Chemical Science and Engineering, School of Materials and Chemical Technology, Tokyo Institute of Technology, 4259 Nagatsuta-cho, Midori-ku, Yokohama, Kanagawa, 226-8502, Japan.
Department of Chemical Science and Engineering, School of Materials and Chemical Technology, Tokyo Institute of Technology, 4259 Nagatsuta-cho, Midori-ku, Yokohama, Kanagawa, 226-8502, Japan.
Department of Chemical Science and Engineering, School of Materials and Chemical Technology, Tokyo Institute of Technology, 4259 Nagatsuta-cho, Midori-ku, Yokohama, Kanagawa, 226-8502, Japan.
Department of Chemical Science and Engineering, School of Materials and Chemical Technology, Tokyo Institute of Technology, 4259 Nagatsuta-cho, Midori-ku, Yokohama, Kanagawa, 226-8502, Japan.
Department of Chemical Science and Engineering, School of Materials and Chemical Technology, Tokyo Institute of Technology, 4259 Nagatsuta-cho, Midori-ku, Yokohama, Kanagawa, 226-8502, Japan.
Department of Chemical Science and Engineering, School of Materials and Chemical Technology, Tokyo Institute of Technology, 4259 Nagatsuta-cho, Midori-ku, Yokohama, Kanagawa, 226-8502, Japan.
Department of Chemistry and Life Science, Yokohama National University, 79-5 Tokiwadai, Hodogaya-ku, Yokohama, Kanagawa, 240-8501, Japan.
Three-point bending test, compression test and tensile test can detect the mechanical properties of the whole layer of skull, but cannot detect the mechanical properties of the inner plate, the diploe...
To seek dentine analogue materials in combined experimental, analytical, and numerical approaches on the mechanical properties and fatigue behaviours that could replace human dentine in a crown fatigu...
A woven glass fibre-filled epoxy (NEMA grade G10; G10) and a glass fibre-reinforced polyamide-nylon (30% glass fibre reinforced polyamide-nylon 6,6; RPN) were investigated and compared with human dent...
The flexural strength of HD (164.27 ± 14.24 MPa), G10 (116.48 ± 5.93 MPa), and RPN (86.73 ± 3.56 MPa) were significantly different (p < 0.001), while no significant difference was observed in their fl...
Even though dentine analogue materials might exhibit similar elastic properties and fatigue performance to human dentine, different reliabilities of fatigue on crown-dentine analogues were shown. RPN ...
Biological particles have evolved to possess mechanical characteristics necessary to carry out their functions. We developed a computational approach to "fatigue testing in silico", in which constant-...
Dental caries is a biofilm-mediated, diet-modulated, multifactorial and dynamic disease that affects more than 90% of adults in Western countries. The current treatment for decayed tissue is based on ...
Dental materials are challenged by wear processes in the oral environment and should be evaluated in laboratory tests prior to clinical use. Many laboratory wear-testing devices are high-cost investme...
The aim of this study was to investigate the in vitro fatigue and fracture force of temporary implant-supported anterior crowns made of different materials with different abutment total occlusal conve...
One hundred ninety-two implant-supported crowns were manufactured (4° or 8° TOC; with/without screw channel) form 6 materials (n = 8; 2 × additive, 3 × subtractive, 1 × automix; reference). Crowns wer...
Kolmogorov-Smirnov, ANOVA; Bonferroni; Kaplan-Meier; log-rank; α = 0.05....
Failure during TCML varied between 0 failures and total failure. Mean survival was between 1.8 × 10...
Additively and subtractively manufactured crowns provided similar or higher survival rates and fracture forces compared to automix crowns. The choice of material is decisive for the survival and fract...
The highest stability has been shown for crowns with a low TOC, which are manufactured additively and subtractively. In automix-fabricated crowns, manually inserted screw channels have negative effect...
To compare and evaluate the compressive and flexural strengths of two resin-based core build-up materials with an alkasite material....
ParaCore, Tetric N ceram Bulk-fill composite, and Cention N were used. A total of 90 specimens were prepared. Customized cylindrical split molds of dimension 6 ± 1 mm (height) × 4 ± 1 mm (diameter) we...
The compressive and flexural strengths of Cention N were significantly less than ParaCore® but higher than Tetric® N-Ceram...
Within the limitations of this study, it was concluded that Cention N may be used as an alternative to other core build-up materials after further...
Cention N had the added advantage that self-cure polymerization alone was sufficient to achieve good physical properties when compared to the other two resin-based core build-up materials....
There have been significant advances in adhesive dentistry in recent decades, with efforts being made to improve the mechanical and bonding properties of resin-based dental adhesive materials. Various...
Studies comparing tensile bond strength of various soft and hard denture liner materials to conventionally and additively manufactured denture base resins are lacking. The purpose of this study was to...
A total of 120 dimethacrylate-based additively manufactured and polymethylmethacrylate (PMMA)-based conventionally fabricated dumbbell-shaped denture-base resins were produced. Heat-cured laboratory-s...
The highest tensile bond strength values were obtained in the specimens from the conventionally manufactured base and self-cured chair-side hard reline material group, and the lowest was seen in the a...
All the specimens used in the present study had tensile bonding stress values for clinical use. Both denture base resins provided an increased bond to the chair-side hard relining material, although a...
The purpose of this in vitro study was to evaluate the microstructural, elemental and mechanical properties of contemporary computer-aided-design/computer-aided manufacturing (CAD/CAM) resin based com...
Six CAD/CAM RBC materials [Brilliant CRIOS (Coltene Whaledent AG), Cerasmart (GC), Lava Ultimate (3M ESPE), Tetric CAD (Ivoclar Vivadent), Shofu Block HC (Shofu), Grandio Blocs (VOCO GmbH)] were teste...
Backscattered Electron images and EDX analysis demonstrated differences in size, shape and type of fillers along with elemental composition among materials tested. Statistical significant differences ...
The results showed that the CAD/CAM materials tested have differences in their microstructure, elemental composition and mechanical properties....
The RBCs tested showed significant differences in mechanical properties and thus differences in clinical performance are anticipated. RBCs with increased filler loading had the most favorable combinat...
