The State Key Laboratory Breeding Base of Basic Science of Stomatology & Key Laboratory for Oral Biomedicine of Ministry of Education, School and Hospital of Stomatology, Wuhan University, Wuhan, China.
Institute of Stomatology, School and Hospital of Stomatology, Wenzhou Medical University, Wenzhou, PR China; Department of Prosthodontics, School and Hospital of Stomatology, Wenzhou Medical University, Wenzhou, PR China.
Institute of Stomatology, School and Hospital of Stomatology, Wenzhou Medical University, Wenzhou, PR China; Department of Prosthodontics, School and Hospital of Stomatology, Wenzhou Medical University, Wenzhou, PR China. Electronic address: dentisitmacn@aliyun.com.
Institute of Stomatology, School and Hospital of Stomatology, Wenzhou Medical University, Wenzhou, PR China; Department of Prosthodontics, School and Hospital of Stomatology, Wenzhou Medical University, Wenzhou, PR China. Electronic address: huangsb003@wmu.edu.cn.
The State Key Laboratory Breeding Base of Basic Science of Stomatology & Key Laboratory for Oral Biomedicine of Ministry of Education, School and Hospital of Stomatology, Wuhan University, Wuhan, China.
Frontier Science Center for Immunology and Metabolism, Wuhan University, Wuhan, China.
Master of Science Program in Geriatric Dentistry and Special Patients Care (International Program), Faculty of Dentistry, Chulalongkorn University, Bangkok, Thailand; Genomics and Precision Dentistry Research Unit, Department of Physiology, Faculty of Dentistry, Chulalongkorn University. Electronic address: thantrira.p@chula.ac.th.
Center of Excellence for Medical Genomics, Medical Genomics Cluster, Department of Pediatrics, Faculty of Medicine, Chulalongkorn University; Excellence Center for Genomics and Precision Medicine, King Chulalongkorn Memorial Hospital, Thai Red Cross Society, Bangkok, Thailand.
Department of Biomedical Sciences and Center for Craniofacial Research and Diagnosis, Texas A&M University College of Dentistry, 3302 Gaston Ave., Dallas, TX, 75246, USA.
Department of Biomedical Sciences and Center for Craniofacial Research and Diagnosis, Texas A&M University College of Dentistry, 3302 Gaston Ave., Dallas, TX, 75246, USA.
The State Key Laboratory Breeding Base of Basic Science of Stomatology & Key Laboratory for Oral Biomedicine of Ministry of Education, School and Hospital of Stomatology, Wuhan University, Wuhan, China.
Frontier Science Center for Immunology and Metabolism, Wuhan University, Wuhan, China.
The State Key Laboratory Breeding Base of Basic Science of Stomatology & Key Laboratory for Oral Biomedicine of Ministry of Education, School and Hospital of Stomatology, Wuhan University, Wuhan, China.
Frontier Science Center for Immunology and Metabolism, Wuhan University, Wuhan, China.
As globalization picks up speed, product innovation-the driving force behind business growth and market competition-becomes increasingly important for advancing product design technology. Computer-aid...
The introduction of computational techniques to pharmaceutical chemistry and molecular biology in the 20th century has changed the way people develop drugs [...]....
Approved or licensed antiviral drugs have limited applications because of their drug resistance and severe adverse effects. By contrast, by stabilizing or destroying the viral capsid, compounds known ...
To evaluate the effect of additive and subtractive manufacturing on the accuracy (trueness and precision) of fixed partial denture patterns (FPDPs) used for casting or pressing....
A 3-unit complete coverage FPD on mandibular right first premolar and first molar teeth was virtually designed. Using the design data, FPD patterns were fabricated from an additively manufactured resi...
Significant differences were found among the RMS values for overall (P<.001) and each surface (P≤.040) evaluated. PR had the highest overall (P≤.011) and intaglio surface (P≤.01) deviations, while the...
BW and YW FPDPs mostly had higher trueness compared with PR FPDPs. However, considering relatively smaller deviations at marginal and intaglio surfaces and the fact that patterns mostly had similar pr...
Definitive 3-unit fixed partial dentures fabricated by using tested patterns may be similar. However, FPDs fabricated with tested additively manufactured resin patterns might result in more chairside ...
The purpose was to investigate the alterations in surface properties of different resin-matrix CAD/CAM ceramics following tooth brushing simulation (TBS) and compare them with a direct resin composite...
Four resin-based CAD/CAM restoratives (Brilliant Crios-BR, Lava™ Ultimate-LV, Grandio Blocs-GR and Shofu Block HC-SH), a leucite-reinforced glass ceramic (IPS Empress® CAD-EC) and a resin composite (F...
After TBS, all the experimental groups exhibited surface loss to different extent. FZ and BR presented the highest surface loss, while EC and GR the lowest (p < 0.05). Regarding surface roughness, all...
The tested resin-matrix CAD/CAM ceramic restorative materials showed a competent behavior against abrasive forces applied during TBS. Surface loss and roughness changes were material dependent and sup...
Tooth brushing affected differently the surface of the tested restorative materials. However, the abrasive wear that was induced was negligible. Clinical studies are necessary to ascertain if there is...
A growing number of out-of-equilibrium systems have been created and investigated in chemical laboratories over the past decade. One way to achieve this is to create a reaction cycle, in which the for...
This study assessed the changes in color stability and biocompatibility of computer-aided design and computer-aided manufacturing (CAD-CAM) glass-ceramics after ultraviolet weathering (UW) aging....
A total of 300 plate-shaped specimens (12.0 × 14.0 × 1.5 mm...
The brightness and redness or greenness were reduced in all groups after aging. After the first aging, V exhibited the largest color change and E exhibited the smallest color change. After the second ...
Leucite-reinforced glass-ceramic exhibit the highest color stability and biocompatibility after aging. The color stability and biocompatibility of CAD-CAM glass-ceramics depend on the aging process an...
Various CAD-CAM glass-ceramics exhibit adequate color stability after UW aging. The leucite-reinforced glass-ceramics exhibit the highest color stability, cell proliferation, and viability after aging...
Computer-aided design/computer-aided manufacturing (CAD/CAM) technology transformed the world of restorative dentistry. The objectives were to assess pre-doctoral dental students' CAD/CAM-related educ...
A total of 358 pre-doctoral dental students from 17 of the 68 US dental schools responded to a web-based anonymous survey....
CAD/CAM-related classroom-based education was likely to happen in lectures (87.2%) and simulated exercises as part of a class (86.9%). Faculty were most likely to provide CAD/CAM instruction (87.9%), ...
The majority of students in the US dental schools appreciate CAD/CAM technology, consider it to be the future of dentistry, and believe it makes them better dentists. The fact that the majority is not...
The purpose of this study was to clarify the discoloration of fiber-reinforced composite resin (FRC) disc materials. The color differences (ΔEs) of three CAD/CAM disc materials, FRC with different fib...
Central nervous system (CNS) disorders are a therapeutic area in drug discovery where demand for new treatments greatly exceeds approved treatment options. This is complicated by the high failure rate...