CAS Key Laboratory of Coastal Environmental Processes and Ecological Remediation, Shandong Key Laboratory of Coastal Environmental Processes, Research Center for Coastal Environmental Engineering and Technology, Yantai Institute of Coastal Zone Research, Chinese Academy of Sciences, Yantai, 264003, China.
Center for Ocean Mega-Science, Chinese Academy of Sciences, Qingdao, 266071, China.
State Key Laboratory of Food Science and Technology, School of Food Science and Technology, National Engineering Research Center for Functional Food, Synergetic Innovation Center of Food Safety and Quality Control, Jiangnan University, Wuxi, Jiangsu, China.
Bioorganic & Biophysical Chemistry Laboratory, Department of Chemistry & Biomedical Sciences, Centre for Biomaterials Chemistry, Linnaeus University, Kalmar, Sweden.
Bioorganic & Biophysical Chemistry Laboratory, Department of Chemistry & Biomedical Sciences, Centre for Biomaterials Chemistry, Linnaeus University, Kalmar, Sweden. ian.nicholls@lnu.se.
CAS Key Laboratory of Coastal Environmental Processes and Ecological Remediation, Shandong Key Laboratory of Coastal Environmental Processes, Research Center for Coastal Environmental Engineering and Technology, Yantai Institute of Coastal Zone Research, Chinese Academy of Sciences, Yantai, 264003, China.
CAS Key Laboratory of Coastal Environmental Processes and Ecological Remediation, Shandong Key Laboratory of Coastal Environmental Processes, Research Center for Coastal Environmental Engineering and Technology, Yantai Institute of Coastal Zone Research, Chinese Academy of Sciences, Yantai, 264003, China.
CAS Key Laboratory of Coastal Environmental Processes and Ecological Remediation, Shandong Key Laboratory of Coastal Environmental Processes, Research Center for Coastal Environmental Engineering and Technology, Yantai Institute of Coastal Zone Research, Chinese Academy of Sciences, Yantai, 264003, China.
Center for Ocean Mega-Science, Chinese Academy of Sciences, Qingdao, 266071, China.
School of Environmental & Municipal Engineering, Qingdao University of Technology, Qingdao, 266033, China.
Three-point bending test, compression test and tensile test can detect the mechanical properties of the whole layer of skull, but cannot detect the mechanical properties of the inner plate, the diploe...
To seek dentine analogue materials in combined experimental, analytical, and numerical approaches on the mechanical properties and fatigue behaviours that could replace human dentine in a crown fatigu...
A woven glass fibre-filled epoxy (NEMA grade G10; G10) and a glass fibre-reinforced polyamide-nylon (30% glass fibre reinforced polyamide-nylon 6,6; RPN) were investigated and compared with human dent...
The flexural strength of HD (164.27 ± 14.24 MPa), G10 (116.48 ± 5.93 MPa), and RPN (86.73 ± 3.56 MPa) were significantly different (p < 0.001), while no significant difference was observed in their fl...
Even though dentine analogue materials might exhibit similar elastic properties and fatigue performance to human dentine, different reliabilities of fatigue on crown-dentine analogues were shown. RPN ...
Biological particles have evolved to possess mechanical characteristics necessary to carry out their functions. We developed a computational approach to "fatigue testing in silico", in which constant-...
Dental caries is a biofilm-mediated, diet-modulated, multifactorial and dynamic disease that affects more than 90% of adults in Western countries. The current treatment for decayed tissue is based on ...
Dental materials are challenged by wear processes in the oral environment and should be evaluated in laboratory tests prior to clinical use. Many laboratory wear-testing devices are high-cost investme...
The aim of this study was to investigate the in vitro fatigue and fracture force of temporary implant-supported anterior crowns made of different materials with different abutment total occlusal conve...
One hundred ninety-two implant-supported crowns were manufactured (4° or 8° TOC; with/without screw channel) form 6 materials (n = 8; 2 × additive, 3 × subtractive, 1 × automix; reference). Crowns wer...
Kolmogorov-Smirnov, ANOVA; Bonferroni; Kaplan-Meier; log-rank; α = 0.05....
Failure during TCML varied between 0 failures and total failure. Mean survival was between 1.8 × 10...
Additively and subtractively manufactured crowns provided similar or higher survival rates and fracture forces compared to automix crowns. The choice of material is decisive for the survival and fract...
The highest stability has been shown for crowns with a low TOC, which are manufactured additively and subtractively. In automix-fabricated crowns, manually inserted screw channels have negative effect...
To compare and evaluate the compressive and flexural strengths of two resin-based core build-up materials with an alkasite material....
ParaCore, Tetric N ceram Bulk-fill composite, and Cention N were used. A total of 90 specimens were prepared. Customized cylindrical split molds of dimension 6 ± 1 mm (height) × 4 ± 1 mm (diameter) we...
The compressive and flexural strengths of Cention N were significantly less than ParaCore® but higher than Tetric® N-Ceram...
Within the limitations of this study, it was concluded that Cention N may be used as an alternative to other core build-up materials after further...
Cention N had the added advantage that self-cure polymerization alone was sufficient to achieve good physical properties when compared to the other two resin-based core build-up materials....
There have been significant advances in adhesive dentistry in recent decades, with efforts being made to improve the mechanical and bonding properties of resin-based dental adhesive materials. Various...
Studies comparing tensile bond strength of various soft and hard denture liner materials to conventionally and additively manufactured denture base resins are lacking. The purpose of this study was to...
A total of 120 dimethacrylate-based additively manufactured and polymethylmethacrylate (PMMA)-based conventionally fabricated dumbbell-shaped denture-base resins were produced. Heat-cured laboratory-s...
The highest tensile bond strength values were obtained in the specimens from the conventionally manufactured base and self-cured chair-side hard reline material group, and the lowest was seen in the a...
All the specimens used in the present study had tensile bonding stress values for clinical use. Both denture base resins provided an increased bond to the chair-side hard relining material, although a...
This study was designed to investigate CAD/CAM restorative blocks and other resin-based materials by (i) determining their chemical composition, (ii) comparing their radiopacity and (iii) correlating ...
Disk specimens, of 1and 2 mm thickness (n = 3), were prepared from five CAD/CAM and six resin-based composites (RBCs). The CAD/CAM resin-composites included aesthetic types: CeraSmart (CS), Grandio Bl...
Radiopacities of CAD/CAM materials were, in ascending order, VE, VM II, CS, LU, and GB. At 1 mm thickness, the radiopacities of all CAD/CAM specimens were matching or slightly lower than enamel. At 2-...
Identifying thin restorations in standard radiographs is necessary with the development and expanded application of 'digital' dental materials in restorative treatment. This study confirmed the joint ...
